Campbell CR23X Spezifikationen PDF herunterladen (Seite 319)

TD ADDENDUM  SECTION 1. FUNCTIONAL MODES

AD-1-3

TABLE 1.5-2. Description of ∗A Mode Data

Keyboard Display

Entry ID: Data

Description of Data

∗

01: XXXX Input Storage Locations (minimum of 28, maximum of 6655,

but the usable maximum is less than this because intermediate

and program storage require some of this memory). This value

can be changed by keying in the desired number.

02: XXXX Intermediate Storage Locations (maximum limited by available

memory and constraints on Input and Final Storage). The

CR10X-TD will assign the exact number needed for the active

program. The CR10X-TD erases all data whenever the program

is changed and compiled.

03: XXXXX Final Storage Locations (minimum of 0, maximum limited by

available memory). Changing this number automatically

reallocates Final Storage Area 1.

04: XXXXX Bytes allocated for user program. The CR10X-TD will assign the

exact number needed. The CR10X-TD erases all data whenever

the program is changed and compiled. Key in 98765 to

completely reset datalogger.

05: Bytes free in Flash Memory for active program. The user

cannot change this window. It is a function of window 5 and the

program.

06: PakBus and user Settings memory

07: Main Memory Free

06: Label Bytes Free

The maximum size of of Final Storage is

determined by the memory installed (Table 1.5-

1). The size of Final Storage and the rate at

which data are stored determines how long it

will take for Final Storage to fill, at which point

new data will write over old.

Twenty-eight is the minimum number of Input

loc

ations allow

ed. Intermediate Storage and

Final Storage are erased when the number of

Input locations is changed. This feature may be

used to clear memory without altering

programming. The number of locations does

not actually need to be changed; the same

value can be keyed in and entered.

Intermediate Storage and Program Memory are

autom

atically

allocated. All data are erased any

time the program is changed and compiled. If

there is not enough memory available in the

32K Main Memory for the Intermediate Storage

required by the current program, the "E:04"

ERROR CODE will be displayed in the ∗0, ∗6,

and ∗B Modes.

After repartitioning memory, the program must be

ecom

piled. Compiling erases Intermediate

Storage. Compiling with ∗0 erases Input Storage;

compiling with ∗6 leaves Input Storage unaltered

(If its size was unchanged).

ENTERING 98765 in the program memory

indow

6 COMPLETELY RESETS THE CR10X.

All memory is erased including the program and

memory is checked. Memory allocation returns

to the default. The reset operation requires

approximately 1 minute for a CR10X, 5 minutes

for a CR10X-1M, and 10 minutes for a CR10X-

2M. Please be patient while the reset takes

place; if the CR10X is turned off in the middle of

a reset, it will perform the reset the next time it is

powered up.

1.6 MEMORY TESTING AND SYSTEM

STATUS - ∗B

No changes from standard operating system,

see datalogger manual.

1.7 ∗C MODE -- SECURITY

No changes from standard operating system,

see datalogger manual.

1.8 ∗D MODE – TRANSFER

PROGRAMS, GENERAL SETTINGS

The ∗D Mode is used to transfer datalogger

programs between a datalogger and a

computer, to erase a program, to set the degree

1 2 ... 314 315 316 317 318 319 320 321 322 323 324 ... 373 374

Campbell CR23X Spezifikationen Seite 319

Kommentare zu diesen Handbüchern

Campbell CR23X Spezifikationen Seite 319

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Messen, Testen & Steuern Campbell CR23X